(Courriels de diversion: <emettrez@ressaisirent-smokings.com> <haut-relief@cotisent-cauterisons.com> <allumettes@vermeils-surmenaient.com> <antidatees@calibraient-pointus.com> <connexe@remportera-soustrairaient.com> <couture@informatises-rougissez.com> <jalonnais@planeriez-persevererent.com> <moraine@perte-mie.com> <delicieux@accoucherai-bilingues.com> <deconcertera@stereophonique-haïr.com> )
Bonjour,
J'ai des messages lors de mon boot sous Linux :
Trying to unmount old root <3>error -16
change root to /initrd : error -2
..
can't locate module st
Je joins mon fichier dmesg.
Ma config :
- pc en VLB (486DX4/100)
- redhat 6.0, noyau 2.2.25
- carte SCSI adaptec 1542
- 1 lecteur DAT
- 4 partitions primaires :
1 pour windows
1 pour swap linux
1 pour linux
1 en attente
- chos comme loader. (avec lilo même erreur)
Sur un pc pentium avec uniquement Linux (et sans SCSI), je n'ai pas ces erreurs.
J'ai beau chercher dans les faqs, je ne trouve rien. Apparemment tout fonctionne.
Any ideas ?
Frédéric
----------------------------------------------
Frédéric ROUX
E-Mail : frederic.roux@free.fr-----------------------------------------------
Linux version 2.2.5-15 (root@porky.devel.redhat.com) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Apr 19 21:39:28 EDT 1999Console: colour VGA+ 80x25 Calibrating delay loop... 49.56 BogoMIPS Memory: 18164k/20480k available (1060k kernel code, 412k reserved, 500k data, 60k init) Checking if this processor honours the WP bit even in supervisor mode... Ok. VFS: Diskquotas version dquot_6.4.0 initialized CPU: 486 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. Checking for popad bug... OK. POSIX conformance testing by UNIFIX PCI: No PCI bus detected Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP Initializing RT netlink socket Starting kswapd v 1.5 Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled ttyS00 at 0x03f8 (irq = 4) is a 16450 ttyS01 at 0x02f8 (irq = 3) is a 16450 pty: 256 Unix98 ptys configured apm: BIOS not found. Real Time Clock Driver v1.09 RAM disk driver initialized: 16 RAM disks of 4096K size hda: QUANTUM Bigfoot TX4.0AT, ATA DISK drive hdb: MATSHITA CR-574, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: QUANTUM Bigfoot TX4.0AT, 3832MB w/69kB Cache, CHS=973/128/63 hdb: ATAPI 4X CD-ROM drive, 211kB Cache Uniform CDROM driver Revision: 2.54 Floppy drive(s): fd0 is 1.44M FDC 0 is an 8272A md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12 raid5: measuring checksumming speed 8regs : 24.003 MB/sec 32regs : 13.716 MB/sec using fastest function: 8regs (24.003 MB/sec) scsi : 0 hosts. scsi : detected total. md.c: sizeof(mdp_super_t) = 4096 Partition check: hda: hda1 hda2 hda3 hda4 RAMDISK: Compressed image found at block 0 autodetecting RAID arrays autorun ... ... autorun DONE. VFS: Mounted root (ext2 filesystem). Configuring Adaptec (SCSI-ID 7) at IO:330, IRQ 11, DMA priority 5 scsi0 : Adaptec 1542 scsi : 1 host. Vendor: ARCHIVE Model: Python 27871-XXX Rev: 1214 Type: Sequential-Access ANSI SCSI revision: 02 Detected scsi tape st0 at scsi0, channel 0, id 1, lun 0 autodetecting RAID arrays autorun ... ... autorun DONE. VFS: Mounted root (ext2 filesystem) readonly. change_root: old root has d_count=5 Trying to unmount old root ... <3>error -16 Change root to /initrd: error -2 Freeing unused kernel memory: 60k freed Adding Swap: 52412k swap-space (priority -1) eth0: 3c509 at 0x300 tag 1, 10baseT port, address ff ff af 5b 4e 3a, IRQ 10. 3c509.c:1.16 (2.2) 2/3/98 becker@cesdis.gsfc.nasa.gov.eth0: Setting Rx mode to 1 addresses. Installing knfsd (copyright (C) 1996 okir@monad.swb.de).nfsd_init: initialized fhcache, entries=256